DIY beef gambrel ideas
-
twilliams said in DIY beef gambrel ideas:
cdavis I gotta ask, is there an advantage to not gutting in the field?
We field dress from a hanging pole with a hand winch near our cabin. It’s nice to field dress there with a water hydrant and outside lighting to see what you are doing at night.
We use ice fishing sleds and 4-wheelers for moving dead deer around so no real lifting and weight is not an issue during transport.
The ice fishing sled also catches the guts, hides, bones and mess. Then it takes a ride back to a designated bone yard away from the cabin. It is all pretty user friendly and minimizes any lifting of stuff. -
twilliams said in DIY beef gambrel ideas:
cdavis I gotta ask, is there an advantage to not gutting in the field?
We field dress from a hanging pole with a hand winch near our cabin. It’s nice to field dress there with a water hydrant and outside lighting to see what you are doing at night.
We use ice fishing sleds and 4-wheelers for moving dead deer around so no real lifting and weight is not an issue during transport.
The ice fishing sled also catches the guts, hides, bones and mess. Then it takes a ride back to a designated bone yard away from the cabin. It is all pretty user friendly and minimizes any lifting of stuff.processhead That sounds like a nice set up, unfortunately we have to transport our deer in pickups to our processing and hanging locations. If the weather is cold they might be in the pickup all day.
-
processhead That sounds like a nice set up, unfortunately we have to transport our deer in pickups to our processing and hanging locations. If the weather is cold they might be in the pickup all day.
bocephus said in DIY beef gambrel ideas:
processhead That sounds like a nice set up, unfortunately we have to transport our deer in pickups to our processing and hanging locations. If the weather is cold they might be in the pickup all day.
Yeah, in that situation it makes total sense to gut them where they drop.
-
Hey all,
Needing ideas for a diy beef gambrel.I was thinking of a piece of I-beam with hooks welded on bottom and a hole on top.
What have you or do you currently used?
Pictures please
knifemaker3 for hanging my moose I use two small chain hoists so that when I cut down the back bone each half stays at the same level. Otherwise when any moose is removed the heavier side goes down. This is so handy I even use it for deer
-
knifemaker3 for hanging my moose I use two small chain hoists so that when I cut down the back bone each half stays at the same level. Otherwise when any moose is removed the heavier side goes down. This is so handy I even use it for deer
Brianzipperdog123 that’s what I’m thinking too. Just a couple chains bolted to the front end loader with a couple hooks and done
-
cdavis would that be heavy enough for hanging a beef?
knifemaker3 mine would not be good for a beef it’s only rated for 450lbs. But man it’s great for deer and hogs.
-
bocephus I love my winch. Can’t go wrong they’re so cheap.
-
cdavis said in DIY beef gambrel ideas:
bocephus I love my winch. Can’t go wrong they’re so cheap.
I have a $30 hand winch rigged up for hoisting deer under an awning behind my shop.
I will never own another block and tackle again. Spend more time untangling and cussing them than actual lifting. -
twilliams I say yes for me there is. Most of my deer are harvested within 4 miles of my house. I can usually tie onto them with the 4wheeler and have them hung within 30 minutes. If I don’t open that cavity until they are hung l figure I’m keeping alot of dirt and debris out of my meat. If I have to track one or If it is exceptionally warm then I gut it right away.
-
Here is a picture of my winch in action this morning
man I love this thing. -
cdavis Very nice, I have the winch, someday I hope to have the shop.
-
Cdavis, I have the same hoist but mine is mounted on an ibeam trolly. Works double duty as deer hanger and Coyote skinning machine.
-
Dr_Pain thanks I enjoy it
-
bocephus I do love my shop.
-
Cdavis, I have the same hoist but mine is mounted on an ibeam trolly. Works double duty as deer hanger and Coyote skinning machine.
-
A good beef gambrel needs to be strong and at about 34" wide. I had one made and spent about $120 on it. Worth every penny. I hang it from a heavy duty chain attached to a tractor bucket.
-
My beef gambrel made by The Hook Shop LLC
-
cdavis
Showed my son your winch setup. Now in his plans for his build. Great idea.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
