Equipment hack
-
@dennyo no offense taken, it was not my intention to write it that way, I just thought I’d throw it in there. It is a brand new stuffer, first time using it. I’m sure it is working as designed, from what I gathered from reviews I just got a different idea in my head
twilliams What size is the horn inot what size casing. That said, I’m sure it is still as you have done. I’m just trying to get a sense of yours maybe against mine.
-
GWG8541 I stepped down to the 11 lb just for the wife as she is the one that cranks while I manage the stuff. With comments being that the crank was easier since the diameter was smaller I chose to get it for that purpose. That is not the case, she had a harder time cranking more than my 20lb. I ended up doing it while I put pressure on casing to fill and she just held it up to get the length I wanted as I stuffed. As far as 11lb goes that is not accurate either. I made two 11lb batches. I only got approximately 8 lbs in and had to refill. The cylinder appears to be thin walled and not as robust. The gears and shaft appear to be very nicely built, not sure what the clicking of every notch in the gear was all about. I thought is was a locking mechanism so it would not back travel but that was not the case. The horn for the 19mm is better than my other one. Maybe I will do a pros and cons list tomorrow
twilliams said in Equipment hack:
GWG8541 I stepped down to the 11 lb just for the wife as she is the one that cranks while I manage the stuff. With comments being that the crank was easier since the diameter was smaller I chose to get it for that purpose. That is not the case, she had a harder time cranking more than my 20lb. I ended up doing it while I put pressure on casing to fill and she just held it up to get the length I wanted as I stuffed. As far as 11lb goes that is not accurate either. I made two 11lb batches. I only got approximately 8 lbs in and had to refill. The cylinder appears to be thin walled and not as robust. The gears and shaft appear to be very nicely built, not sure what the clicking of every notch in the gear was all about. I thought is was a locking mechanism so it would not back travel but that was not the case. The horn for the 19mm is better than my other one. Maybe I will do a pros and cons list tomorrow
Good feedback. Reading your review, it almost read like the stuffer I bought on Amazon (Hakka 7 lbs). I wonder if Walton farmed it out to the same company??
-
twilliams What size is the horn inot what size casing. That said, I’m sure it is still as you have done. I’m just trying to get a sense of yours maybe against mine.
@dennyo I will have to take the horn to work and measure with my calipers. My other one is 12.7mm outside diameter and I have to basically force my 19mm casing on the horn. The Walton’s one the casing goes right on with a little play so I’m assuming maybe a 10mm. Which explains with it being more difficult to crank but with the smaller diameter canister and piston of less down pressure I would think maybe they would equal out to the same crank pressure?
-
3/8" +/- is prety small to be pushing the 11 lb stuffer into.
-
@dennyo I will have to take the horn to work and measure with my calipers. My other one is 12.7mm outside diameter and I have to basically force my 19mm casing on the horn. The Walton’s one the casing goes right on with a little play so I’m assuming maybe a 10mm. Which explains with it being more difficult to crank but with the smaller diameter canister and piston of less down pressure I would think maybe they would equal out to the same crank pressure?
twilliams Are you saying you used a 12.7mm o.d. and stuffed with a larger stuffer canister diameter?
Denny O’s-Smokey Bones
I’d rather be sit’in in a boat and thinking about God,
Than sit’n in church and thinking about fish’in! -
The other night was my first time stuffing 22mm sheep casings with the 11# Walton’s stuffer and between cranking and feeding the casings by myself I found it considerably easier to sit down and pull down on the handle from 12 o’clock to the 6 o’clock position and then move the handle back up to 12 o’clock and start over. It allowed me to pull straight down which seemed to give me more power and control to avoid blowouts, that’s my very limited experience and two cents worth.
-
twilliams Are you saying you used a 12.7mm o.d. and stuffed with a larger stuffer canister diameter?
@dennyo yes my old cabelas 20 lb canister is quite a bit bigger with the 12.7mm horn that came with it. I will do some measurement comparison tonight when i get home.
-
twilliams Are you saying you used a 12.7mm o.d. and stuffed with a larger stuffer canister diameter?
@dennyo here is the measurement differences of the two horns and stuffer canisters
-
twilliams Are you saying you used a 12.7mm o.d. and stuffed with a larger stuffer canister diameter?
@dennyo
-
@dennyo yes my old cabelas 20 lb canister is quite a bit bigger with the 12.7mm horn that came with it. I will do some measurement comparison tonight when i get home.
-
twilliams Your Waltons stiffer looks a lot like my LEM 11# 2 speed. The horn on the Cabellar seems to be working a lot of reduction! I suppose there is no chance that you could switch the horns?? (I know, you have already tried that too, duh.
All of you talk about a clicking noise, Why would that be a normal sound??
Denny O’s-Smokey Bones
I’d rather be sit’in in a boat and thinking about God,
Than sit’n in church and thinking about fish’in! -
Tried finding the meat hacks post but couldn’t find it. I think it was Dr_Pain that came up with the therapy balls to squeeze the rest of the meat out of the throat of the stuffer which is a wonderful way to do it. Here is my hack that I do.
I used to buy all cabelas equipment before I found meatgistics and Walton’s. The pic you see which is Saturday the 8th and is my very first time using the 11lb sausage stuffer from Walton’s. My hack is to take my long tube jerky shooter and add the left over meat from the stuffer throat and into the tube, then take the stuffing horn from the Walton’s stuffer and finish out the casing. There is a little left in the horn and I will find some type of plunger to get that out at a later date.twilliams there is a different company out there that sells these. They come in a few different sizes. A metal plunger to clear out the tube and then a brush for cleaning. Thought about trying them instead of using a wooden spoon handle (mine are actually plastic) I even thought about buying a couple different size dowel rods to try.
-
twilliams there is a different company out there that sells these. They come in a few different sizes. A metal plunger to clear out the tube and then a brush for cleaning. Thought about trying them instead of using a wooden spoon handle (mine are actually plastic) I even thought about buying a couple different size dowel rods to try.
Randie N I like the dowel rod idea. Right now, I’m doubling plastic wrap over the end of the next smaller stuffing tube and using that as a plunger. It works but add another tube to clean.
-
twilliams Your Waltons stiffer looks a lot like my LEM 11# 2 speed. The horn on the Cabellar seems to be working a lot of reduction! I suppose there is no chance that you could switch the horns?? (I know, you have already tried that too, duh.
All of you talk about a clicking noise, Why would that be a normal sound??
@dennyo I’m doing another 25 lbs today so I will be doing a test. The first flavor I will use the Walton’s horn the second flavor will be using the cabelas horn with the Walton’s stuffer. I will post results
-
twilliams Your Waltons stiffer looks a lot like my LEM 11# 2 speed. The horn on the Cabellar seems to be working a lot of reduction! I suppose there is no chance that you could switch the horns?? (I know, you have already tried that too, duh.
All of you talk about a clicking noise, Why would that be a normal sound??
@dennyo well after the test there is absolutely no difference in crank pressure from the Walton’s horn to the cabelas horn. I was surprised. On a positive note the crank pressure was so much less today, really baffles me because I used 100ml less of water on this batch compared to last weekends batch.
-
@dennyo well after the test there is absolutely no difference in crank pressure from the Walton’s horn to the cabelas horn. I was surprised. On a positive note the crank pressure was so much less today, really baffles me because I used 100ml less of water on this batch compared to last weekends batch.
twilliams So, you have done the first batch out of a Waltons stuffer and their tube and it was very hard to crank.
Now you have tried both tubes in the Waltons stuffer and are feeling it is the same as the old Cabelas stuffer. But still harder to crank than you thought it should be bu reducing the canister size.
Dang, wish you were closer, I’d let you play with my LEM 2 speed. I have yet to say that it cranks hard. I’m not advocating LEM now mind you, I’m thinking that your new 11# Waltons and My 11# Lem I’ll bet are very simularly built. This still makes me thing there is an issue with your stuffer.
Have you reached out to Waltons customer service?
Denny O’s-Smokey Bones
I’d rather be sit’in in a boat and thinking about God,
Than sit’n in church and thinking about fish’in! -
twilliams So, you have done the first batch out of a Waltons stuffer and their tube and it was very hard to crank.
Now you have tried both tubes in the Waltons stuffer and are feeling it is the same as the old Cabelas stuffer. But still harder to crank than you thought it should be bu reducing the canister size.
Dang, wish you were closer, I’d let you play with my LEM 2 speed. I have yet to say that it cranks hard. I’m not advocating LEM now mind you, I’m thinking that your new 11# Waltons and My 11# Lem I’ll bet are very simularly built. This still makes me thing there is an issue with your stuffer.
Have you reached out to Waltons customer service?
@dennyo no I haven’t contacted them and I won’t. I’m not unhappy with the stuffer, it is just not what I was expecting compared to my other one. It does make me interested now to know how the 20lb Walton’s cranks compared to my 20lb Cabelas. I would prefer a bigger canister so I don’t have to refill. I’m not buying another one though, my next purchases are gonna be a vac tumbler, vac chamber, commercial dehydrator and 15”slicer.
-
@dennyo well after the test there is absolutely no difference in crank pressure from the Walton’s horn to the cabelas horn. I was surprised. On a positive note the crank pressure was so much less today, really baffles me because I used 100ml less of water on this batch compared to last weekends batch.
twilliams You are getting stronger…
-
twilliams You are getting stronger…
calldoctoday would be nice if that was the case
-
calldoctoday would be nice if that was the case
twilliams a 15" slicer, wholey Carp! Hobart or??
You better have a place for the forklift to set it! Cause you ain’t gonna be moving it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
