This is a suggestion for the Sausage stuffers!
-
Miket482000 Jonathan talked about this how they are working on having such a handle actually designed for the new stuffer! Would be awesome incorporated in the original handles!
-
I retrofitted my antique stuffers with an extended handle that essentially does the same thing. One end is always on the downstroke. The added length gives extra leverage when doing snack sticks.
I do like the idea of a ratchet though.
-
Miket482000 My mistake I got it in my brain that you were talking about a meat mixer. You might be able to get away with a breaker bar. Easier to find in a longer length than a ratchet.
YooperDog A breaker bar would still require taking it of and putting it back on in a new position and you would still need a socket to fit the stud on the stuffer so a ratchet handle preferably a 1/2 inch drive would work great I would think as most of them are about the same length or a little longer than the original handle.
-
I retrofitted my antique stuffers with an extended handle that essentially does the same thing. One end is always on the downstroke. The added length gives extra leverage when doing snack sticks.
I do like the idea of a ratchet though.
processhead That would work well too. the only problem with the stuffer I have is that the stud is not square it is splined so nothing really fits well unless you machine something to fit it. I have an Idea using some plastic wrap and wax on the stud, then some JB weld in a socket that is a little bigger than the drive stud on the Mixer. I am going to try that in a few days to see if it will hold and take the tork.
-
processhead That would work well too. the only problem with the stuffer I have is that the stud is not square it is splined so nothing really fits well unless you machine something to fit it. I have an Idea using some plastic wrap and wax on the stud, then some JB weld in a socket that is a little bigger than the drive stud on the Mixer. I am going to try that in a few days to see if it will hold and take the tork.
Miket482000 Not mixer I meant to say Stuffer
-
processhead That would work well too. the only problem with the stuffer I have is that the stud is not square it is splined so nothing really fits well unless you machine something to fit it. I have an Idea using some plastic wrap and wax on the stud, then some JB weld in a socket that is a little bigger than the drive stud on the Mixer. I am going to try that in a few days to see if it will hold and take the tork.
Miket482000 They make square drive sockets that fit the shaft. Just look for an 8 point socket. It will fit the shaft exactly and tight and you will be able to use a long handled ratchet to turn it. They look like this www.[link removed]/Stanley-Proto-J52109-5-piece-8-point/dp/B01H2YWI4C/ref=asc_df_B01H2YWI4C/?tag=hyprod-20&linkCode=df0&hvadid=330443528285&hvpos=&hvnetw=g&hvrand=17108450847114869075&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9061299&hvtargid=pla-718546574807&psc=1 Add Amazon for link removed
-
Miket482000 They make square drive sockets that fit the shaft. Just look for an 8 point socket. It will fit the shaft exactly and tight and you will be able to use a long handled ratchet to turn it. They look like this www.[link removed]/Stanley-Proto-J52109-5-piece-8-point/dp/B01H2YWI4C/ref=asc_df_B01H2YWI4C/?tag=hyprod-20&linkCode=df0&hvadid=330443528285&hvpos=&hvnetw=g&hvrand=17108450847114869075&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9061299&hvtargid=pla-718546574807&psc=1 Add Amazon for link removed
johnsbrewhouse said in This is a suggestion for the Sausage stuffers!:
tanley-Proto-J52109-5-piece-8-point
I will take a look at that and see, it seems like I tried to fit one of those already, but I may be mistaken. I will have to check again.
-
johnsbrewhouse said in This is a suggestion for the Sausage stuffers!:
tanley-Proto-J52109-5-piece-8-point
I will take a look at that and see, it seems like I tried to fit one of those already, but I may be mistaken. I will have to check again.
Miket482000 You may have tried an inverted Torx bit, they are different from 8 point sockets. 8 point sockets are actually made for square nuts.
-
Miket482000 They make square drive sockets that fit the shaft. Just look for an 8 point socket. It will fit the shaft exactly and tight and you will be able to use a long handled ratchet to turn it. They look like this www.[link removed]/Stanley-Proto-J52109-5-piece-8-point/dp/B01H2YWI4C/ref=asc_df_B01H2YWI4C/?tag=hyprod-20&linkCode=df0&hvadid=330443528285&hvpos=&hvnetw=g&hvrand=17108450847114869075&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9061299&hvtargid=pla-718546574807&psc=1 Add Amazon for link removed
johnsbrewhouse The 8 point socket does not work! It fits, but does not go into the groves far enough and when under pressure it slips. I has a hard time getting the socket off as it had twisted on the shaft far enough to get jammed on top of the ridges. It was a good fit no slop when on the shaft, just not enough slot engagement. I actually think Processheads solution is a better option than the ratchet as there is a fair amount of back pressure you can not simply raise the handle to ratchet back. you have to grab the shaft and hold it to prevent it from rotating backwards. Granted this is still faster than taking the handle off and then refitting it, it is less of an advantage than his double ended handle would be in my opinion.
-
Miket482000 You may have tried an inverted Torx bit, they are different from 8 point sockets. 8 point sockets are actually made for square nuts.
johnsbrewhouse Is there a torx socket? that is what would be necessary. I also don’t recall torx having the same number of splines as the handle shaft has. An 8 point socket fits well just does not go into the spline slots deep enough to hold.
-
johnsbrewhouse Is there a torx socket? that is what would be necessary. I also don’t recall torx having the same number of splines as the handle shaft has. An 8 point socket fits well just does not go into the spline slots deep enough to hold.
Miket482000 while not common, there are deep 8 point sockets available.
-
Before I bought A new stuffer from Walton’s I used A 16 mm 12 point socket 1/2 drive instead of my handle and it worked well. With the Walton’s stuffer I have found that the handle works well. My old stuffer was A garage sale special that the ratchet worked well with to give me more control of the speed.
-
maybe now that Walton’s are selling their own equipment they can design something that the masses are wanting !
-
maybe now that Walton’s are selling their own equipment they can design something that the masses are wanting !
I love the idea of the 1/2" drive. So then then you could run your stuffer with one of these.
-
Miket482000 while not common, there are deep 8 point sockets available.
Chef just did a search and did not see any if you have a source let me know.
-
Chef just did a search and did not see any if you have a source let me know.
-
ive thought of this too. i am able to clamp the crank side of mine so on the up stroke it doesnt lift the stuffer which works fine but i totally see your point.
opah73 It is not just the lifting it is also more difficult to operate on the up stroke of the crank. Many times I am operating by my self and it is a pain, but when I have a helper they are not always even able to turn it in that fission. So my objective is to just make it easier to operate for me or a child or someone that just is not as capable.
-
johnsbrewhouse LOL not going to buy a whole set to be sure. If there is a place to get individual socket i would give it a try, but they don’t seem to be any different than the 8 point impact sockets I already have.
-
I love the idea of the 1/2" drive. So then then you could run your stuffer with one of these.
IVERYAN even in the slowest setting im in belief that the impact would run too fast , have too much torque and you would tear the gears into smitherings
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
