Weston tenderizer compatability
-
samspade It LOOKS like it will hook up. johng can you possibly do some measurements and see if that will hook up? I know that ours is a 6 spline but I don’t know if the hole around the grinder head will accept that. So, we would need to measure the hole or compartment that contains the 6 spline hookups diameter and the 6 splines hook up section.
-
JohnG5 ok my spline length looks right. Is the spline diameter 18mm from valley to valley (shorter) or ridge to ridge
Does the weston grider model do both tenderizing and jerkey slicing. It looks like you can get accessory blades for the table top model but not the grinder attachment model? I guess this should probably go through customer serv. So let me know if it’s a bother.
-
so I’m not going to get a direct fit for the spine. I could modify the spine to increase the spine size from 18 to 21 to fit.
From my pictures does the rest of the unit look like they would mate up? -
Don’t want to interfere, but isn’t it female on your grinder and male on the tenderizer?
-
Don’t want to interfere, but isn’t it female on your grinder and male on the tenderizer?
Grimpuppy I’m an idiot! The grinder is female. The tenderizer is male. I got mixed up and was thinking how much I would have to cur off to make the smaller spines fit the larger hole.
It’s the old " I’ve. Cut twice but it’s still to short’ thought process -
Cool. Does the grinder tenderizer have both jerky and cubbing blade or is the jerky blades an accessory. The only blades for jerky I have seen look like the hand crank model
-
Gonna drop my 2 cents again. You have 21mm major diameter shaft and 16mm minor diameter shaft on your grinder. You subtract the two measurements and that is 5mm difference. You divide that by half and you get 2.5mm tooth engagement right now. If you use an 18mm shaft, you are losing 3mm of major diameter. That brings your 5mm down to 2mm. You divide that by half and you will only have 1mm of engagement with the 18mm shaft. 1mm is 1/32”, that aint much left.
3mm may not seem like much, but when you only have 5mm to start with it is a lot. I think you are going wear your female coupling from not enough tooth engagement. Just my opinion.
-
Grimpuppy thank you. I am over thinking this I think. Considering looking at a new grinder coupler in case the wear does become an issue. I wonder if there would really be alot of wear considering the use would be residential use not commercial. It just the price for a grinder meat tenderizer is about half of the table mount hand tenderizer.
I really appreciate any response as someone may go in a direction I hadn’t thought about. -
Ok, bought a used weston tenderizer. The spline matches the spine of the grinder almost. Just a little loose but I dont believe the torque needed to run the tenderizer will damage the grinder. The problem is the head of the tenderizer is to large to go into the grinder. I maybe able to find a machinist to take 3mm off the tenderizer head and drill a small dimple for the grinder pin.
-
Took a while but the machenist was able to grind the stainless steel collar down. Just put it together and it looks like a good fit. Now waiting for weston to get a replacement spline so I can have the cuber and jerky slicer ready to use without changing splines.
Pictures to follow once it’s all together.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
