What does everyone use for hot smoking.
-
@NDMike I use a pellet grill set it at 150° pull summer sausage when it hits 130-140° finish in water with electric roaster
blackbetty61 i thought about doing that but my lowest setting on my pellet grill is 185. I could cold smoke and sous vide though!
-
@NDMike
Takes about 6.5 hours from start to pulling out for a 25 lb batch for snack sticks. Temps range from starting at 110° to stepping up slowly to 170° to finish. 240volt electric saw dust smoker
twilliams i want one bad but the wife doesn’t like the $1800 price tag!!!
-
I use a 25 cu ft kenmore freezer converted to burn charcoal in a hibachi controlled by a digiq que control works great
-
twilliams that is an awesome looking machine. What do they sell for if you don’t mind me asking.
cdavis $9200 if you upgrade to the electronic controller like mine. The electronic controller is either a $1200 or $1800 upgrade, cant remember which. I got $1000 off due to some weld blemishes (appearance only, not structural)
-
twilliams that is an awesome looking machine. What do they sell for if you don’t mind me asking.
-
@NDMike well she really wouldnt go for the price tag on mine then…lol. Just tell her, but honey the other ones dont last so we will be buying 10 of those compared to one pk…your saving her money and you get your toy then, its a win win. Plus she gets to eat all the yummies
-
I know it’s a long shot. But check Craigslist. I did and got my PK100 for $275… it does happen.
Life is a Garden - Dig it.
-
I know it’s a long shot. But check Craigslist. I did and got my PK100 for $275… it does happen.
lkrfletcher that is one clean looking smoker.
-
lkrfletcher that is one clean looking smoker.
YooperDog Not so much anymore. The guy I got it from cleaned the heck out of it. I really wish he hadn’t, I had to re-season it. Good to go now. I bought 4 new shelves and a bowl from Walton’s and I am all set for $275
-
PK 100 for me, too.
-
Home-build electrically heated smoker with pellet feeder for smoke generation. This used to be a hospital blanket warmer in its previous life.
Originally it had separate upper and lower compartments, so the center partition had to come out.
Then cut openings in the top and bottom for air intake and vent. The old heating elements were only 400 watts so I install a 2400 watt oven element in the bottom. The old analog controls came out and I installed a second-hand digital PID temperature controller and temp probe.For the smoke source, I basically copied and build a pellet feed auger system and burn chamber with a small heat element igniter. I wasn’t happy with the igniter element and chamber and did a recent modification where I put in a pellet burn pot and igniter stick like is used in most pellet smokers and grills.
This has been an ongoing work in progress with tweeks along the way where I felt improvements were needed.I liked the fact that the original box was well insulated and well sealed. It is tight enough that I can run it in my basement without smoking up the house. It vents smoke out of the house through an abandoned furnace flue.
Paul
-
Home-build electrically heated smoker with pellet feeder for smoke generation. This used to be a hospital blanket warmer in its previous life.
Originally it had separate upper and lower compartments, so the center partition had to come out.
Then cut openings in the top and bottom for air intake and vent. The old heating elements were only 400 watts so I install a 2400 watt oven element in the bottom. The old analog controls came out and I installed a second-hand digital PID temperature controller and temp probe.For the smoke source, I basically copied and build a pellet feed auger system and burn chamber with a small heat element igniter. I wasn’t happy with the igniter element and chamber and did a recent modification where I put in a pellet burn pot and igniter stick like is used in most pellet smokers and grills.
This has been an ongoing work in progress with tweeks along the way where I felt improvements were needed.I liked the fact that the original box was well insulated and well sealed. It is tight enough that I can run it in my basement without smoking up the house. It vents smoke out of the house through an abandoned furnace flue.
processhead Looks like a work of art!Verry nice!
-
processhead Looks like a work of art!Verry nice!
RON PARRISH said in What does everyone use for hot smoking.:
processhead Looks like a work of art!Verry nice!
Thanks, Ron. I enjoy building and servicing equipment almost as much as making sausage.
-
Home-build electrically heated smoker with pellet feeder for smoke generation. This used to be a hospital blanket warmer in its previous life.
Originally it had separate upper and lower compartments, so the center partition had to come out.
Then cut openings in the top and bottom for air intake and vent. The old heating elements were only 400 watts so I install a 2400 watt oven element in the bottom. The old analog controls came out and I installed a second-hand digital PID temperature controller and temp probe.For the smoke source, I basically copied and build a pellet feed auger system and burn chamber with a small heat element igniter. I wasn’t happy with the igniter element and chamber and did a recent modification where I put in a pellet burn pot and igniter stick like is used in most pellet smokers and grills.
This has been an ongoing work in progress with tweeks along the way where I felt improvements were needed.I liked the fact that the original box was well insulated and well sealed. It is tight enough that I can run it in my basement without smoking up the house. It vents smoke out of the house through an abandoned furnace flue.
processhead
Home build? Wow! That’s great! -
cdavis the pk100 is i believe around $1700, i just decided to go with grand daddy of the ProSmokers
twilliams I have to say that is the best looking smoker I have ever seen. But I don’t see one in my future. Congrats
-
Home-build electrically heated smoker with pellet feeder for smoke generation. This used to be a hospital blanket warmer in its previous life.
Originally it had separate upper and lower compartments, so the center partition had to come out.
Then cut openings in the top and bottom for air intake and vent. The old heating elements were only 400 watts so I install a 2400 watt oven element in the bottom. The old analog controls came out and I installed a second-hand digital PID temperature controller and temp probe.For the smoke source, I basically copied and build a pellet feed auger system and burn chamber with a small heat element igniter. I wasn’t happy with the igniter element and chamber and did a recent modification where I put in a pellet burn pot and igniter stick like is used in most pellet smokers and grills.
This has been an ongoing work in progress with tweeks along the way where I felt improvements were needed.I liked the fact that the original box was well insulated and well sealed. It is tight enough that I can run it in my basement without smoking up the house. It vents smoke out of the house through an abandoned furnace flue.
-
looks good like a home built pk 100
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
