Pk 100 blew up
-
Update on the smoker, I can not thank Jeff and his team enough for helping me resolve my issue. The customer service that I recieved from Pro Smoker was over the top to say the least. They got me back smoking in short order, If you are looking for a smoker this one should be at the top of your list. Thanks again Jeff.
Phantom any explanation on thoughts of diagnosis?
-
My only thought after speaking with Jeff was that I had it on high, switched it to low for smoking but didn’t give it time to cool the burner before putting dry sawdust on? Just my thoughts im sure they are looking into it
Phantom I’m glad you were very pleased with their response and action
May I ask, what was the response and action? -
Update on the smoker, I can not thank Jeff and his team enough for helping me resolve my issue. The customer service that I recieved from Pro Smoker was over the top to say the least. They got me back smoking in short order, If you are looking for a smoker this one should be at the top of your list. Thanks again Jeff.
-
This is old, but I will throw this in concerning sawdust.
I used to do chemistry experiments on gases and products released during charcoal manufacture. I would take a 1pint paint can with a copper pipe soldered thru top, so it could be sealed airtight to keep oxygen out. Add 1 cup of sawdust and heat. A large plastic garbage bag, like 50 gallons, would be taped on top.By heating sawdust without O2, methane gas is given off in huge amounts. I could collect 2 full 50 gallon inflated bags of methane gas from 1c of sawdust!
I used the methane to drive bunsen burners for various distillation or messing around. Also collected would be 2 T or more of acetic acid, like vinegar, collected in the bags.In any case, that is for sure enough methane to blow a smoker up if ignited. So, scenario: mostly sealed smoker, little O2 inside. Heat sawdust without ventilation, get 50 to 100 gallons of ambient pressure methane built up in there. One single granule of anything in there igniting, any sawdust smoldering, would ignite the methane. Methane air mixes have been shown to ignite constantly from light alloy sparks. We would tape a model rocket electic ignition squib in the bag, and set them off for quite the good flash.
I would not heat sawdust in low o2 low airflow airtight environment that could be later subjected to ignition source after gas buildup. The whole gradual electical element heating of sawdust in an enclosed chamber where you’re hoping at some point it gets hot enough to begin smoldering is a setup for methane air mix explosion. I’m amazed it doesn’t happen more often. Far safer is already smoldering pellets/wood to produce smoke, like an external smoke daddy etc.
-
This is old, but I will throw this in concerning sawdust.
I used to do chemistry experiments on gases and products released during charcoal manufacture. I would take a 1pint paint can with a copper pipe soldered thru top, so it could be sealed airtight to keep oxygen out. Add 1 cup of sawdust and heat. A large plastic garbage bag, like 50 gallons, would be taped on top.By heating sawdust without O2, methane gas is given off in huge amounts. I could collect 2 full 50 gallon inflated bags of methane gas from 1c of sawdust!
I used the methane to drive bunsen burners for various distillation or messing around. Also collected would be 2 T or more of acetic acid, like vinegar, collected in the bags.In any case, that is for sure enough methane to blow a smoker up if ignited. So, scenario: mostly sealed smoker, little O2 inside. Heat sawdust without ventilation, get 50 to 100 gallons of ambient pressure methane built up in there. One single granule of anything in there igniting, any sawdust smoldering, would ignite the methane. Methane air mixes have been shown to ignite constantly from light alloy sparks. We would tape a model rocket electic ignition squib in the bag, and set them off for quite the good flash.
I would not heat sawdust in low o2 low airflow airtight environment that could be later subjected to ignition source after gas buildup. The whole gradual electical element heating of sawdust in an enclosed chamber where you’re hoping at some point it gets hot enough to begin smoldering is a setup for methane air mix explosion. I’m amazed it doesn’t happen more often. Far safer is already smoldering pellets/wood to produce smoke, like an external smoke daddy etc.
Dave in AZ Thanks for the input to the smoker blowup question. The scenario you describe seems very plausible for sawdust smokers.
-
This is old, but I will throw this in concerning sawdust.
I used to do chemistry experiments on gases and products released during charcoal manufacture. I would take a 1pint paint can with a copper pipe soldered thru top, so it could be sealed airtight to keep oxygen out. Add 1 cup of sawdust and heat. A large plastic garbage bag, like 50 gallons, would be taped on top.By heating sawdust without O2, methane gas is given off in huge amounts. I could collect 2 full 50 gallon inflated bags of methane gas from 1c of sawdust!
I used the methane to drive bunsen burners for various distillation or messing around. Also collected would be 2 T or more of acetic acid, like vinegar, collected in the bags.In any case, that is for sure enough methane to blow a smoker up if ignited. So, scenario: mostly sealed smoker, little O2 inside. Heat sawdust without ventilation, get 50 to 100 gallons of ambient pressure methane built up in there. One single granule of anything in there igniting, any sawdust smoldering, would ignite the methane. Methane air mixes have been shown to ignite constantly from light alloy sparks. We would tape a model rocket electic ignition squib in the bag, and set them off for quite the good flash.
I would not heat sawdust in low o2 low airflow airtight environment that could be later subjected to ignition source after gas buildup. The whole gradual electical element heating of sawdust in an enclosed chamber where you’re hoping at some point it gets hot enough to begin smoldering is a setup for methane air mix explosion. I’m amazed it doesn’t happen more often. Far safer is already smoldering pellets/wood to produce smoke, like an external smoke daddy etc.
Dave in AZ that is great information. Thanks for sharing.
-
Glad no one was hurt. Yes, sawdust with the right moisture levels, temps, etc. can be extremely volatile or explosive. Have seen homes being renovated with wood floor refinishing & caught on fire from excessive airborne wood dust from the refinishing process. I think I will definitely stick to chips & chunks.
-
My only thought after speaking with Jeff was that I had it on high, switched it to low for smoking but didn’t give it time to cool the burner before putting dry sawdust on? Just my thoughts im sure they are looking into it
I can not say enough good things about the guys at PK!! they were easy to work with very helpful, and in the end sent me a new unit. Honestly it was the Holy Grail of customer service!! the kind you dream of but never find. Thanks to Jeff and all at PK for your help.
-
This is old, but I will throw this in concerning sawdust.
I used to do chemistry experiments on gases and products released during charcoal manufacture. I would take a 1pint paint can with a copper pipe soldered thru top, so it could be sealed airtight to keep oxygen out. Add 1 cup of sawdust and heat. A large plastic garbage bag, like 50 gallons, would be taped on top.By heating sawdust without O2, methane gas is given off in huge amounts. I could collect 2 full 50 gallon inflated bags of methane gas from 1c of sawdust!
I used the methane to drive bunsen burners for various distillation or messing around. Also collected would be 2 T or more of acetic acid, like vinegar, collected in the bags.In any case, that is for sure enough methane to blow a smoker up if ignited. So, scenario: mostly sealed smoker, little O2 inside. Heat sawdust without ventilation, get 50 to 100 gallons of ambient pressure methane built up in there. One single granule of anything in there igniting, any sawdust smoldering, would ignite the methane. Methane air mixes have been shown to ignite constantly from light alloy sparks. We would tape a model rocket electic ignition squib in the bag, and set them off for quite the good flash.
I would not heat sawdust in low o2 low airflow airtight environment that could be later subjected to ignition source after gas buildup. The whole gradual electical element heating of sawdust in an enclosed chamber where you’re hoping at some point it gets hot enough to begin smoldering is a setup for methane air mix explosion. I’m amazed it doesn’t happen more often. Far safer is already smoldering pellets/wood to produce smoke, like an external smoke daddy etc.
Dave in AZ Thanks for the info. Another reason to always keep your vents properly opened while you have a bowl of sawdust on the burner.
-
Thread on Smokin It forums to this gas ignition phenomenon
Looks like this is a pretty common occurrence in airtight smokers when wood is first heated, gasses off methane, then wood ignition happens. Sounds like the smokin it has enough of a vent that it doesn’t blow up, just fireballs out vent…
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
