Walton's Mixer with other grinders
-
Sorry for the late reply. I’m at work doing my 24 hour shift. I’ll get a picture when I get home. I bought my grinder in 2019, just before the most recent change and incidentally just before I found Waltons. If I’m being honest, had I found Walton’s and Meatgistics before I bought the grinder, I’d have gotten it from Walton’s. The business is just too good not to support. Especially
Austin and 
Jonathon I know where I’ll be buying my next grinder whether I up-size or replace my current one.badfire2625 what changes were made in '19?
If the women don’t find you handsome, they should at least find you handy - Red Green
-
badfire2625 what changes were made in '19?
smokinbubba honestly I don’t know. I decided on a #12 and went there because I got reward points on my Southwest account. The new ones look substantially different but then again I was only looking online. I went with the Walton’s mixer not knowing if it would connect to the grinder because it has the handle so I knew I wouldn’t be left hanging if it didn’t connect. I had a long honey do list before I left for work (overtime) so I didn’t get a picture today. On a happy note, and relating to another post, I did get a few seconds to check the progress and taste of my blood orange wine and so far so good.
-
Your carnivore looks identical to all i have seen on the shelf at Cabelas and my new #22. I dont think any changes were made in the carnivore line since they have been in production.
If the women don’t find you handsome, they should at least find you handy - Red Green
-
Your carnivore looks identical to all i have seen on the shelf at Cabelas and my new #22. I dont think any changes were made in the carnivore line since they have been in production.
This is what the old cabelas (pre carnivore) grinders look like. This is my #12 20210219_091950.jpg
If the women don’t find you handsome, they should at least find you handy - Red Green
-
This is what the old cabelas (pre carnivore) grinders look like. This is my #12 20210219_091950.jpg
-
smokinbubba Here’s three shots. The first is off of the Cabelas site of the new grinder, the second is a side view of mine and the third is the hub and splines. I didn’t have a tape measure with me. I am working on my fire to get dinner smoked right now (while I finally have some time at home…) It’s fairly obvious that they either went with a new manufacturer or just updated the aesthetics. The on/off switch is different, the drawer is in a different position and the shrouding around the motor is a lot different. I feel bad talking about a competitor’s brand on Walton’s site but I hope it can help people until they find the need to upgrade their grinder and maybe move to a Walton’s.
-
WOW, there is a difference. My #22 looks just like yours with the storage drawer on the front. The newest rendition has the drawer on the side. Mine does have a reverse switch tho as do all sizes currently sold. So there are different “generations” of the cabelas carnivore grinders. I doubt Austin and Jon mind us talking about competitors grinders since we are really trying to find other grinders that their mixer will fit. I may be wrong. I know many folks want to buy the Walton’s mixer but are scared that it wont fit a grinder they already have. Look at the Q&A section on their mixer at Waltons inc. Lots of people are asking what the mixer will fit. When you get a chance, please measure the hub and see if it is close to 2.5" so we can share the findings. Thx
If the women don’t find you handsome, they should at least find you handy - Red Green
-
WOW, there is a difference. My #22 looks just like yours with the storage drawer on the front. The newest rendition has the drawer on the side. Mine does have a reverse switch tho as do all sizes currently sold. So there are different “generations” of the cabelas carnivore grinders. I doubt Austin and Jon mind us talking about competitors grinders since we are really trying to find other grinders that their mixer will fit. I may be wrong. I know many folks want to buy the Walton’s mixer but are scared that it wont fit a grinder they already have. Look at the Q&A section on their mixer at Waltons inc. Lots of people are asking what the mixer will fit. When you get a chance, please measure the hub and see if it is close to 2.5" so we can share the findings. Thx
smokinbubba will do. I’m once again at work… I hope they don’t mind us talking about this. What I hope to do is generate more sales for them because this community has done a lot for me already. The obvious choice is to get Walton’s equipment when able or needed. That is what I’m going to do.
-
My new 50# Waltons mixer fits on my LEM #8. Ran over 200# through it Saturday. My son was thinking he was getting a cheap grinder since I purchased a #32. Sorry
Grandpa butchered 80 hogs the year he was 80. I buy pork butts to make sausage.
-
My new 50# Waltons mixer fits on my LEM #8. Ran over 200# through it Saturday. My son was thinking he was getting a cheap grinder since I purchased a #32. Sorry
RandyNight what does your LEM hub measure? Is it a perfect fit 3/4"x 6 spline shaft?
-
The ID of the LEM hub is 2.125. The 3/4 x 6 spline shaft seems to fit perfectly. Saturday our daughter made a mistake mixing the seasonings on a 25 lb batch and we had to double it and it turned the overfull mixer load fine.
Grandpa butchered 80 hogs the year he was 80. I buy pork butts to make sausage.
-
The ID of the LEM hub is 2.125. The 3/4 x 6 spline shaft seems to fit perfectly. Saturday our daughter made a mistake mixing the seasonings on a 25 lb batch and we had to double it and it turned the overfull mixer load fine.
RandyNight So, is the waltons mixer hub 2"?? Now I see how the Waltons mixer will fit many grinder manufacturers. (this is good!) A 2" mixer hub will fit any grinder hub larger than 2" but obviously not smaller. IE: LEM at 2.125, Cabelas 2.5
seems everyone uses a 3/4" x 6spline shaft to drive it allLooks like Cabelas mixers will only fit Cabelas grinders with both being 2.5" Go figure…
-
The ID of the LEM hub is 2.125. The 3/4 x 6 spline shaft seems to fit perfectly. Saturday our daughter made a mistake mixing the seasonings on a 25 lb batch and we had to double it and it turned the overfull mixer load fine.
RandyNight This speaks volumes as to the quality of the Waltons mixer. I would never do that with my Cabelas unit! I don’t have that much faith in the gears.
-
Walton mixer hub just a bit over 2" but a slip fit
-
My new 50# Waltons mixer fits on my LEM #8. Ran over 200# through it Saturday. My son was thinking he was getting a cheap grinder since I purchased a #32. Sorry
RandyNight You happen to have a picture of the two mated up?
-
Grimpuppy It still set up from our last sausage day
-
-
No go with Grandpa’s #12 Stimson, it has a square shaft!
Grandpa butchered 80 hogs the year he was 80. I buy pork butts to make sausage.
-
No go with Grandpa’s #12 Stimson, it has a square shaft!
RandyNight said in Walton's Mixer with other grinders:
No go with Grandpa’s #12 Stimson, it has a square shaft!
I’ll bet that old beast has heard a few stories over the years!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
