Cabelas meat mixer
-
smokinbubba Yeah, Cabelas isnt really a competitor…I guess they are actually, but sausage making/meat processing is a very small portion of what they do and it is basically everything we do! I like Cabelas so I don’t want to think of them as a competitor.!
Jonathon so when is Mr. Walton going to open a store in Ohio? Kansas is about 4" on the map and thats 3.5" too far for me to drive!
-
smokinbubba Yeah, we found that it APPEARS as if some manufacturers made changes to their units to prevent them working across lines, trying to force people to buy their line in both grinders and mixers. We are working on our mixers now trying to make some improvement but one thing we will not do is try to make changes so it only works with Walton’s equipment. That seems pointless to me and a good way to make people not happy with you.
Jonathon I was looking into buying the Waltons 50lbs mixer after bad experiences with the Weston 44lbs version. However, you mentioned that you guys are looking into changes. Would you reccomend to wait? Also, does the Waltons mixer have less parts? The weston had a lot of small parts that could easily be lost.
-
Jl. What grinder do you plan to power it with or are you gonna crank it?
If the women don’t find you handsome, they should at least find you handy - Red Green
-
Jl. What grinder do you plan to power it with or are you gonna crank it?
-
Ok. Here is an update and a weird one at that. I happened to pickup a older cabelas non carnivore #12 yesterday. Couldn’t pass it up for the price. $40 anyway, I believe these were made by Weston and look exactly like the butcher series. It couples up perfectly to my new 50 lb cabelas mixer designed for the carnivore series. If this is made by Weston their 44 lb mixer should fit it too. Right?
But popasop measured his Weston 44lber and its hub measures 2”. The cabelas measures 2.5. Scratching head now…
So lesson so far is the older cabelas grinders will fit the new cabelas 50lb mixer and vice versa.smokinbubba I was doing the same research when I bought my mixer and was having a hard time getting any info from the manufacturer about their spline shaft sizes. What I did find though was adapter couplings online so I wasn’t too worried that I wouldn’t be able to get something rigged up if the shaft sizes were different. My backyard butcher grinder ended up matching up to Walton’s 40# mixer though so I didn’t have to use an adapter.
-
The spline on LEM products seem to be different than cabelas and Weston. The cabelas/Weston are all 3/4” by 6 spline. The problem is with the hub that connects the mixer to the grinder motor. This hub is where the big hand screw threads in to lock the two together or the grinder to the motor. These vary between 2” to 2.5” on the units I have researched.
-
Brandekm Also, backyard pro looks just like a Weston butcher series. They are offered by webstaurant supply and they claim to be the manufacturer. What size backyard do u have? I’m looking for a measurement on the inside diameter of the neck tube on a backyard #12
-
Brandekm Also, backyard pro looks just like a Weston butcher series. They are offered by webstaurant supply and they claim to be the manufacturer. What size backyard do u have? I’m looking for a measurement on the inside diameter of the neck tube on a backyard #12
smokinbubba an adapter shaft would work like an extension and you wouldn’t have to worry about the hub size since they won’t mate anyways. I have a #22 and the grinder throat is a little over 2 inches wide.
-
I have a Cabellas grinder and I bought the 50lb mixer at BPS to attach to it. I used the mixer for 1 min and 40 seconds before it broke . After looking on line and calling Blue Sky it is a common problem with the way they welded the idle pulley in the gear box . Long story short if you get the 50lb mixer from BPS or cabelas before you use it i would take the gear box off and open it then either weld or JB weld epoxy both sides of the gear box where the idle pulley goes .
-
smokinbubba Yeah, we found that it APPEARS as if some manufacturers made changes to their units to prevent them working across lines, trying to force people to buy their line in both grinders and mixers. We are working on our mixers now trying to make some improvement but one thing we will not do is try to make changes so it only works with Walton’s equipment. That seems pointless to me and a good way to make people not happy with you.
Jonathon Yep I was really happy when I found my new Waltons 50# mixer will work with my #8 LEM. My son thought he was gonna snag a deal on the LEM since I have the new Waltons #32. Sorry, son.
-
I have a Cabellas grinder and I bought the 50lb mixer at BPS to attach to it. I used the mixer for 1 min and 40 seconds before it broke . After looking on line and calling Blue Sky it is a common problem with the way they welded the idle pulley in the gear box . Long story short if you get the 50lb mixer from BPS or cabelas before you use it i would take the gear box off and open it then either weld or JB weld epoxy both sides of the gear box where the idle pulley goes .
Tim Bailey Very common problem with these. I figure I will have my welder at work tig it back if/when it lets loose! There is only one option for the carnivore grinders and its the blue sky 50lber. I wish someone would come out with a 20lb model so I didnt have to do my small batches in the kitchen aid.
-
S smokinbubba referenced this topic on
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
