Meat grinder issues
-
Austin this is a great example of what you have built here, meat processors from the other side of the world trying to help each other out, pretty freaking great!
-
twilliams facebook.com/doptrading/photos/pcb.105902424518065/105901634518144/ manual for the machine. You can’t buy any part for the grinder housing, it comes as an assembly. I went through a bunch on sites, nobody breaks it down.
-
twilliams the grinder is actually an Orimas TBS-200 but it does look just like the taisin grinder pictured. I’ve seen this same model under a few different brand names here, I think all made in the same factory but just sold by different distributors who put there own badge on it.
-
johnsbrewhouse the bearing number is 620srs which is clearly available online for replacements. I’m no bearing expert but I would’ve thought that even if it’s a sealed bearing, that seal is never going to be very good and I’ll always have contamination issues from one batch to the next unless I change the bearing each time.
-
twilliams mine didn’t come with that large plastic washer/bush. Just a small one that sits between the auger and the bearing as pictured here
 
-
This post is deleted!
-
johnsbrewhouse the bearing number is 620srs which is clearly available online for replacements. I’m no bearing expert but I would’ve thought that even if it’s a sealed bearing, that seal is never going to be very good and I’ll always have contamination issues from one batch to the next unless I change the bearing each time.
kksmokehouse sealed bearings are usually pretty good about holding their seal. The automotive industry has been using them for years in wet locations and under light pressure. I would not think there would be a problem in the grinder unless moisture intruded into the bearing. I would hope they were packed with a food grade lubricant as well, which it does not appear to be. That would be my concern as well if the seal were to fail. I really would just continue to use it as is and maybe use some food safe grease between the auger and bearing on every use to create a barrier. Then I would check the bearing after you do your clean up for seal break down and see if the bearing is getting rough from moisture intrusion
-
twilliams sorry, struggling to get these photos up.
-
kksmokehouse sealed bearings are usually pretty good about holding their seal. The automotive industry has been using them for years in wet locations and under light pressure. I would not think there would be a problem in the grinder unless moisture intruded into the bearing. I would hope they were packed with a food grade lubricant as well, which it does not appear to be. That would be my concern as well if the seal were to fail. I really would just continue to use it as is and maybe use some food safe grease between the auger and bearing on every use to create a barrier. Then I would check the bearing after you do your clean up for seal break down and see if the bearing is getting rough from moisture intrusion
johnsbrewhouse the grinder is only about a month old. I think the seal on the bearing is either gone already or was defective from the get-go. What I can see is a dark looking, thick grease coming out from between the bearing’s inner ring and black seal. I’ve been told that the bearing is pressed in so I’m going to track down a better quality sealed bearing and have someone with a bearing press replace it… Might be back to the hand grinder while getting this sorted.
-
Is the grinder new? may be a defective bearing
Johnsbrewhouse bronze bearing idea is good if you can access a machine shop.glen said in Meat grinder issues:
Is the grinder new? may be a defective bearing
kksmokehouse said in Meat grinder issues:
johnsbrewhouse the grinder is only about a month old. I think the seal on the bearing is either gone already or was defective from the get-go. What I can see is a dark looking, thick grease coming out from between the bearing’s inner ring and black seal. I’ve been told that the bearing is pressed in so I’m going to track down a better quality sealed bearing and have someone with a bearing press replace it… Might be back to the hand grinder while getting this sorted.
I assume there is no warranty solution?
-
glen said in Meat grinder issues:
Is the grinder new? may be a defective bearing
kksmokehouse said in Meat grinder issues:
johnsbrewhouse the grinder is only about a month old. I think the seal on the bearing is either gone already or was defective from the get-go. What I can see is a dark looking, thick grease coming out from between the bearing’s inner ring and black seal. I’ve been told that the bearing is pressed in so I’m going to track down a better quality sealed bearing and have someone with a bearing press replace it… Might be back to the hand grinder while getting this sorted.
I assume there is no warranty solution?
glen the shop gives a 3 month warranty to cover motor related problems only unfortunately. They don’t seem to think the bearing issue is an issue at all
-
glen the shop gives a 3 month warranty to cover motor related problems only unfortunately. They don’t seem to think the bearing issue is an issue at all
kksmokehouse That sucks, wish you the best, hope you find a solution
-
The bearing is sealed and can be replaced. There should be a number on the bearing seal, the black part. There is also a bushing behind the bearing which I find odd. You could find a local machine shop which I’m sure they have in Malaysia that could turn a replacement bushing for the bearing out of bronze or Oilite bronze
johnsbrewhouse are you saying you think the bearing is possibly not necessary and could just be replaced by a bronze or olite bronze bushing of the same inner and outer diameter/depth? I presume I’d then want to have that pressed in so it provides full support for the auger and allows it spin freely within?
-
kksmokehouse yes that is quite the different set up. Not sure what engineering was thinking on that one. Even though that is supposed to be a sealed bearing surely i wouldnt think it would keep out liquid. Im not sure on what advice to give you that would be food safe afterwards. Is that bearing able to be pulled out or do you think it was pressed in? There might be some holes on the back side of where the bearing is where you could use a punch and tap it out lightly with a small hammer for cleaning purposes
-
twilliams just to confirm, this kind of set up (bearing located just behind the auger in the wet part of the grinder) is not common with grinders sold in the US? Even larger commercial models?
kksmokehouse yes you are correct, mine has a hard plastic bushing.
-
johnsbrewhouse are you saying you think the bearing is possibly not necessary and could just be replaced by a bronze or olite bronze bushing of the same inner and outer diameter/depth? I presume I’d then want to have that pressed in so it provides full support for the auger and allows it spin freely within?
kksmokehouse That would be right. You would just have to make sure to add a food grade lube to the shaft each time you assemble it. Most all US grinders use bushings rather than a bearing. They are probably using a bearing due to cost, That bearing probably fit s many applications and it’s only about $3 US retail. I can get them even cheaper as a company and probably even less in bulk.
-
kksmokehouse yes you are correct, mine has a hard plastic bushing.
twilliams My Weston has plastic bushing and washers as well
-
twilliams and johnsbrewhouse thank you both, really appreciate your help! Its a shame about this grinder because it actually does a really good, fast and efficient job. At the end of the day, I just need it to be more hygienic. I think whatever bearing is in there, good quality food safe or cheap standard (as I think it came with off the shelf), once you add hot water and detergents and give it a scrub, it’s going to start to flush the packed grease out pretty quick and rust. I will either look at getting a custom bronze bush, which seems pretty difficult here, or I will splash and import something (LEM/Walton) from the US. Cheers.
-
twilliams and johnsbrewhouse thank you both, really appreciate your help! Its a shame about this grinder because it actually does a really good, fast and efficient job. At the end of the day, I just need it to be more hygienic. I think whatever bearing is in there, good quality food safe or cheap standard (as I think it came with off the shelf), once you add hot water and detergents and give it a scrub, it’s going to start to flush the packed grease out pretty quick and rust. I will either look at getting a custom bronze bush, which seems pretty difficult here, or I will splash and import something (LEM/Walton) from the US. Cheers.
kksmokehouse Best of luck either way my friend. I would have thought you might have been able to find a small machine shop somewhere there. Of course Malaysia is fairly large but small and depends where you are located. Glad we could at least give you some help and ideas.
-
Would shipping the grinder head to a machine shop be cost prohibitive? Seems a shame to not get that grinder back in the game.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
