First time snack sticks and thermo processing
-
Sous vide = going to bed at a decent hour.
-
Modern smokers have a lot of controls and temp sensors which we have come to be very dependent on.
It is good to have an accurate backup thermometer that you can trust when things just don’t seem right. -
Sous vide = going to bed at a decent hour.
smokinbubba My first run of snack sticks with the sous vide was today.
“You never really die until you end up on the wall at a Cracker Barrel”
-
smokinbubba My first run of snack sticks with the sous vide was today.
GWG8541 looking good. I use a turkey roaster right now, but will be going that route hopefully soon. It is like going going from bottling to kegging.
-
I like my finished snack sticks somewhat dry and I am wondering about if that is even possible when finishing sticks in hot water? The only thing I can think of is letting them air dry in the refrigerator after all thermal processing is done, before packaging.
Paul
-
I like my finished snack sticks somewhat dry and I am wondering about if that is even possible when finishing sticks in hot water? The only thing I can think of is letting them air dry in the refrigerator after all thermal processing is done, before packaging.
processhead I let mine air dry in the fridge and they get like a salami and a solid snap. Kabanosy makes a good stick, growing up the local shops would have them hanging on the rack with their other cured sausages in varying stages of dryness. Probably wouldn’t float today.
-
processhead I let mine air dry in the fridge and they get like a salami and a solid snap. Kabanosy makes a good stick, growing up the local shops would have them hanging on the rack with their other cured sausages in varying stages of dryness. Probably wouldn’t float today.
-
taufrecht 30 hours for snack sticks is way too long so there are a few things that could be going on here. (sorry, I know we’ve kind of moved on but I wanted to point this out)
You might have gotten case hardening, where the outside of the casing either cooks or dries too quickly. At -8 I hope you warmed up your smoker first and then tried to keep the doors open for short periods while you loaded it? Adding humidity is a good way to increase the thermal processing energy as it fights off the stall and helps convey the heat more effectively into the meat.
Last thing, it COULD be an issue with your PK-100. I remember someone else saying something similar recently. I hope they don’t have a bad batch of controllers or something out there. Using a thermometer that can check the ambient temperature in the smoker is probably idea.And, of course, finishing in water speeds everything up!
-
I like my finished snack sticks somewhat dry and I am wondering about if that is even possible when finishing sticks in hot water? The only thing I can think of is letting them air dry in the refrigerator after all thermal processing is done, before packaging.
processhead i bloom mine with a fan blowing on them. Works good.
If the women don’t find you handsome, they should at least find you handy - Red Green
-
processhead i bloom mine with a fan blowing on them. Works good.
smokinbubba the term “bloom” i dont quite understand, the look of my snack stix, summer sausage and ring bologna has the same look from finished out of smoker to 20 minute ice bath to 1 hour set dry time and after overnight in fridge before packaging. So not really sure on the term or what it is supposed to do
-
Bloom is basically a resting period after the ice bath. Some smoked products will develop a nice mahogany color. It also dries a little. It really helps my sticks that were finished in sous vide. Didnt see much color change in thise tho.
-
I used the MEATER thermometer. The internal ambient temperature never got close to the setting of the PK100. I even set it up to 250 degrees at high watt setting. The temperature never got above 150.
What would be my next step?taufrecht call customer service at proSmoker
-
Could be several things causing that.
- Bad temperature probe telling the controls that it is hotter than it actually is, so the controller doesn’t call for the element to turn on.
- Bad control board.
- Bad or intermittent wire connection between control board and the element.
- Bad heating element. Usually when they go bad, you will get zero heat .
Depending on your skills and comfort troubleshooting electrical power equipment, you may want to have a technician look at it for you.
Paul
-
Could be several things causing that.
- Bad temperature probe telling the controls that it is hotter than it actually is, so the controller doesn’t call for the element to turn on.
- Bad control board.
- Bad or intermittent wire connection between control board and the element.
- Bad heating element. Usually when they go bad, you will get zero heat .
Depending on your skills and comfort troubleshooting electrical power equipment, you may want to have a technician look at it for you.
processhead i assume it is under warranty, if that is the case only a certified technician can dive into it.
-
Yes, if its under warranty, exhaust all those options first.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
