Snack stick blues
-
bobfrapples
I had the same problem with my cast iron stuffer when making small diameter sticks. They just don’t have the mechanical advantage you need to push the meat through that tiny stuffer tube.I made a longer handle for more leverage. It works wonders and makes the old cast iron stuffers usable for stuffing snack sticks.
-
That’s genius, I love that idea.
-
The hardest part was coming up with a 1/2 inch square drive that would fit on the pinion gear of the stuffer. You might be able to make out the modified 1/2 drive socket I welded on to the square tubing for the handle.
-
bobfrapples 1st, welcome to this site. 2nd there are a few things you said that could help you. 1st, don’t mix the day before and then stuff. Add a cure accelerator and go right from mixing to stuffing to smoking OR go from mixing to stuffing to holding if you do not use a cure accelerator. The meat will start to setup over night and it will make it harder to stuff. 2nd, how much water are you actually adding? 3rd make sure your seal is positioned the right way, our seals on our 7,11,26, and 33 lb stuffers don’t orientate the way it would make sense to a lot of people. The gap goes down if that makes sense? 4th make sure your meat it super cold during the stuffing process, you DONT want ice crystals but you do want everything, especially the fat to be super cold so it isn’t as sticky. Finally, what is your fat content?
Look forward to hearing from you!
-
The hardest part was coming up with a 1/2 inch square drive that would fit on the pinion gear of the stuffer. You might be able to make out the modified 1/2 drive socket I welded on to the square tubing for the handle.
processhead I did notice the socket, I have a few extras and some square tubing I have laying around that I’ll try to rig up. Great idea, thanks for the input.
-
bobfrapples 1st, welcome to this site. 2nd there are a few things you said that could help you. 1st, don’t mix the day before and then stuff. Add a cure accelerator and go right from mixing to stuffing to smoking OR go from mixing to stuffing to holding if you do not use a cure accelerator. The meat will start to setup over night and it will make it harder to stuff. 2nd, how much water are you actually adding? 3rd make sure your seal is positioned the right way, our seals on our 7,11,26, and 33 lb stuffers don’t orientate the way it would make sense to a lot of people. The gap goes down if that makes sense? 4th make sure your meat it super cold during the stuffing process, you DONT want ice crystals but you do want everything, especially the fat to be super cold so it isn’t as sticky. Finally, what is your fat content?
Look forward to hearing from you!
Jonathon makes sense on the cure accelerator and going straight to stuffing, thanks.
I’m not exactly sure how much water I was adding, I only know that I added what I thought was a lot of water, had trouble, added more, to then getting blasted in the face with meat and water once the seal broke. Haha, it was quite the sight to see. And yes, I tried different setups with the seal thinking I might have it wrong but it blew out no matter how I tried it.
As for fat content, we used 50% beef(brisket) and 50% venison.
-
processhead I did notice the socket, I have a few extras and some square tubing I have laying around that I’ll try to rig up. Great idea, thanks for the input.
bobfrapples
While a 1/2 socket is a close fit, I still had to heat it cherry red with a torch and then press it on to the end of the pinion gear for a proper fit. ( after removing the pinion gear from the stuffer. -
You might try looking up four point or pipe plug sockets
-
I also stripped the gears on a cheapish stuffer, but reworked the mounting system, took out the crank, and installed a linear actuator (12 v, 330 lbs thrust) with a transformer and bidirectional switch. Works great, now!
It’s a 5-lber, and I have a load of horns for it. Kitchen counter for size, lazy susan for sausage pickup to make it an easy 1-person job. Maybe you can do something similar.
Cheers from chilly Winnipeg! -
Where did you find your actuator? That looks sorta like the one on the dump box of my UTV.
Great looking retrofit. -
I also stripped the gears on a cheapish stuffer, but reworked the mounting system, took out the crank, and installed a linear actuator (12 v, 330 lbs thrust) with a transformer and bidirectional switch. Works great, now!
It’s a 5-lber, and I have a load of horns for it. Kitchen counter for size, lazy susan for sausage pickup to make it an easy 1-person job. Maybe you can do something similar.
Cheers from chilly Winnipeg!Harkness pretty ingenious
-
Where did you find your actuator? That looks sorta like the one on the dump box of my UTV.
Great looking retrofit. -
glen an 8 point socket will work auto parts or farm supply , they use square
bolts on farm equipment -
When using a conventional stuffer Instead of using a crank, I use a socket and a 1/2" ratchet which enables you to pull all the time and not have to push on the back stroke which is a lot harder for old fellows.
-
There’s also the “Universal Socket Fit” on Amazon and Ebay which is essentially a socket with rods that fit around the head/deformed or not; they start at various external diameters and work down. If that’s the way you want to go, ebay is cheapest and Amazon is quickest. Cost is inverse to speed. Cheers from Winnipeg!
-
bobfrapples
I had the same problem with my cast iron stuffer when making small diameter sticks. They just don’t have the mechanical advantage you need to push the meat through that tiny stuffer tube.I made a longer handle for more leverage. It works wonders and makes the old cast iron stuffers usable for stuffing snack sticks.
-
bobfrapples If the seal was the right way and you had so much water and pressure that it broke the seal and splashed yu in the face I’d guess something is blocking your tube? I never asked what size stuffing tube you were using? Is it possible that a chunk of something blocked the tube? I have experimented with stuffing partially frozen meat, and if it gets blocked what you are describing can happen.
-
I also stripped the gears on a cheapish stuffer, but reworked the mounting system, took out the crank, and installed a linear actuator (12 v, 330 lbs thrust) with a transformer and bidirectional switch. Works great, now!
It’s a 5-lber, and I have a load of horns for it. Kitchen counter for size, lazy susan for sausage pickup to make it an easy 1-person job. Maybe you can do something similar.
Cheers from chilly Winnipeg! -
bobfrapples If the seal was the right way and you had so much water and pressure that it broke the seal and splashed yu in the face I’d guess something is blocking your tube? I never asked what size stuffing tube you were using? Is it possible that a chunk of something blocked the tube? I have experimented with stuffing partially frozen meat, and if it gets blocked what you are describing can happen.
Jonathon the stuffing tube doesn’t have a label but I think it’s an un-tapered 12mm. I don’t think anything was blocking the end because it happened too many times. However, I did some closer inspection last night and the seal does have a little nick in it, not sure if this happened before our struggle or during our struggle but I’d suspect that could be a big reason as well.
Some very good points and ideas on here, thanks everyone. Now it’s decision time for me, fix “cheap” stuffer, improve cast iron stuffer as shown above, or buy one of the stuffers on this website. I must admit, the smooth elbow at the bottom, having 2 different crank speeds, etc. seem like a big advantage. From what I’ve read and seen online, they also look very well built.
.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
