Summer Sausage casing hard to remove
-
Midgetracer31 After the cook did you water bath them? My brother makes the larger ring bologna and he ice baths them, he says we were told that it bring a thin layer of fat to the surface and make the casing separate easier.
-
Midgetracer31 How much water did you add?
-
Midgetracer31 After the cook did you water bath them? My brother makes the larger ring bologna and he ice baths them, he says we were told that it bring a thin layer of fat to the surface and make the casing separate easier.
-
Midgetracer31 The only thing I can think of is an ice bath vs water bath then. I am going to be doing some Summer Sausage out of wild game tomorrow, I will try putting one in just cold water and switching that out a time or two versus an ice bath. Maybe that will give us some insight but other than that I can’t come up with anything. Unless we want to start talking about the pH at different stages of the cook cycle and even for that I would need our application specialist to analyze the information, which would have to be live.
Hopefully, doing the water bath vs ice bath shows us something. I am doing those tomorrow, so by Thursday, or Friday at the latest, I will hopefully have an answer.
-
Midgetracer31 Sorry, i see that now, I’d try an ice bath not just cold water and fully submerse them. He uses a ton of ice in a 5 gallon bucket, the rings fit perfect in them.
-
Midgetracer31 The only thing I can think of is an ice bath vs water bath then. I am going to be doing some Summer Sausage out of wild game tomorrow, I will try putting one in just cold water and switching that out a time or two versus an ice bath. Maybe that will give us some insight but other than that I can’t come up with anything. Unless we want to start talking about the pH at different stages of the cook cycle and even for that I would need our application specialist to analyze the information, which would have to be live.
Hopefully, doing the water bath vs ice bath shows us something. I am doing those tomorrow, so by Thursday, or Friday at the latest, I will hopefully have an answer.
Jonathon I will say this the time before this which was my first run at summer sausage the result was the same. That time I use the Sodium Erythorbate additive no sure gel was added, it used a not pre stuck casing from LEM I think 2" or 2-1/4" size. I didnt have my powered mixer so that was done in my 22lb Weston manual mixer, so it defiantly was not over mixed. We did a 80% pork/ 20% chicken breast mix and a reverse of that 80% chicken breast/20%pork. Both was close in flavor tough casing removal was equal.
-
Midgetracer31 Did you do the water bath on both batches? Sorry to keep harping on that but it keeps sticking out in my mind. Like I said, I am doing some tomorrow and smoking it on Thursday so I will test it out.
-
1.5in X 12in Mahogany Pre-Stuck Fibrous Casing is what I used ground pork shoulder for meat , smoked and cooked to 165 in cabinet with water pan for moisture. Water bath until cooled down, left out for hour at room temp, then to fridge. Casing is rather smooth coming out of smoker cabinet then thru cooling take a wrinkled set. We slice it and then slit it and the casing rarely strips away clean it pulls a small bit of meat usually. FYI mixed meat in Weston 44lb power mixer, did add some super gel to the mix, good tight stuff and hog ringed. Followed your recommended thermal processing schedule. Have I missed something??
Midgetracer31
Very strange. Used the exact same casings this past weekend and hit 165 in 6.5 hrs. -
I would say two things i would do different. I would mix it longer. With a hand mixer i would go honestly about 14 minutes. If its not mixed good enough it will attach itself to the casing as well. But as others have said your problem is cooling it down. 165 degrees is pretty hot. Id go 160 degrees. But at 165 when you pull them they are real hot and want to keep climbing very fast. They will start to wrinkle and attach to the casings within a few minutes if you dont start cooling immediently. Grab a garden hose and pull them out and hang them and start spraying the second they come out and dont quit spraying for about 30 minutes. Then let hang for an hour. If you do this stuff they will be perfect for you.
-
I would say two things i would do different. I would mix it longer. With a hand mixer i would go honestly about 14 minutes. If its not mixed good enough it will attach itself to the casing as well. But as others have said your problem is cooling it down. 165 degrees is pretty hot. Id go 160 degrees. But at 165 when you pull them they are real hot and want to keep climbing very fast. They will start to wrinkle and attach to the casings within a few minutes if you dont start cooling immediently. Grab a garden hose and pull them out and hang them and start spraying the second they come out and dont quit spraying for about 30 minutes. Then let hang for an hour. If you do this stuff they will be perfect for you.
lamurscrappy
As far as cooling I totally agree. Thought with a 5# batch I could just rinse in the sink with a cold spray for a few minutes. Didn’t work. Did the ice bath and done deal. -
lamurscrappy
As far as cooling I totally agree. Thought with a 5# batch I could just rinse in the sink with a cold spray for a few minutes. Didn’t work. Did the ice bath and done deal.PapaSop ya its a bad deal. Go through all the work to make them, then the very last process can screw them up!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
