My incredible auction find....
-
A few weeks ago I picked up a Weston 20# mixer for $20 at a local auction… While I would love to be here gloating over my awesome find, instead I need some advice…
I have tried everything I can to remove the mixing paddle, but the spring loaded knob will just not pull back quite far enough to allow it to release… I’ve tried everything, including trying to spread the sides of the mixer to get that little bit more play to release the paddle…
Anyway, Im out of ideas… I have even stooped to downloading the user guide for the mixer and following the instructions
Any tips, hints or trade secrets about how to remove that thing would be appreciated…
Screw the Big knob in to pull the Brass pin back to get the auger out
-
Denny Thanks, but I didn’t just fall off the turnip truck… been there, done that, got the half cleaned mixer to prove it…
-
raider2119 Let me play around with mine for a while and I will see if there is anything I can offer. What Denny said is true the tighter you screw that bog knob the less it allows the spring to push back in against the shaft so it SHOULD give you more room. I’m guessing you’ve got a rusted spring somewhere. Have you tried shooting it with some Blaster or even just DW-40?
I’ll play around with it a little this morning as I am sure you can’t be the only person having this issue and see what I can come up with.
-
-
Okay, Im sure you’ve already done this but in the one on the left the knob is screwed in and somewhat loose, on the left it is screwed in all the way AND I am pulling back on it, it drags the thicker part back into the recess. Also, I assume you have removed the screw and the handle from the other side and pulled out the brass piece over there as well?
I assume you have tried that as you attempted to spread out the sides. I’d try shooting some blaster or wd40 from both the inside and around the knob area and let it sit on its side a little. I think it is most likely going to be a rusty spring or rust on the threads and that blaster stuff is pretty amazing at dealing with rust.
-
Okay, Im sure you’ve already done this but in the one on the left the knob is screwed in and somewhat loose, on the left it is screwed in all the way AND I am pulling back on it, it drags the thicker part back into the recess. Also, I assume you have removed the screw and the handle from the other side and pulled out the brass piece over there as well?
I assume you have tried that as you attempted to spread out the sides. I’d try shooting some blaster or wd40 from both the inside and around the knob area and let it sit on its side a little. I think it is most likely going to be a rusty spring or rust on the threads and that blaster stuff is pretty amazing at dealing with rust.
Jonathon I have not tried WD-40 yet, the brass piece on the knob end seems to move freely, and seems to have full range of travel… just not far enough to allow the mixer paddle to slip free… There is no rust, in fact, this appears to be brand new… don’t even see any scratches on the plastic lid…
I have removed the handle / crank, but the brass piece on that side is still in the mixer… It appears this inserts from the inside, and to remove it the paddle must be removed first… am I somehow wrong about this?
-
Jonathon I have not tried WD-40 yet, the brass piece on the knob end seems to move freely, and seems to have full range of travel… just not far enough to allow the mixer paddle to slip free… There is no rust, in fact, this appears to be brand new… don’t even see any scratches on the plastic lid…
I have removed the handle / crank, but the brass piece on that side is still in the mixer… It appears this inserts from the inside, and to remove it the paddle must be removed first… am I somehow wrong about this?
-
-
raider2119 Yes, you should be able to slide that brass piece out of the mixer while the shaft still inside the mixer. It should pull out fairly easily, at least it does on mine!
-
raider2119 I have found both assembly and disassembly as well as cleaning to be cumbersome on mine. I haven’t used it much because of that.
-
raider2119 Yes, you should be able to slide that brass piece out of the mixer while the shaft still inside the mixer. It should pull out fairly easily, at least it does on mine!
Jonathon will try in a few mins… vice grips in hand!
Thanks!!! -
Joe Hell Yes, cleaning the mixer can be a pain but in general I find it is much easier to use when making anything larger than a 5 lb batch. That might be because my hands get super cold though and we keep everything just about icing when processing. Someone on here suggested cotton gloves underneath the nitrile gloves and that helps but I’m a bit of a sissy when it comes to being cold!
Get more help with your processing questions and learn more about processing meat by subscribing to our waltonsinc.com youtube page at https://wltns.link/waltonstv I am a Gorilla, love yourself
-
Joe Hell Yes, cleaning the mixer can be a pain but in general I find it is much easier to use when making anything larger than a 5 lb batch. That might be because my hands get super cold though and we keep everything just about icing when processing. Someone on here suggested cotton gloves underneath the nitrile gloves and that helps but I’m a bit of a sissy when it comes to being cold!
-
Joe Hell I can’t stick my foot in a bucket of ice water if I sprain an ankle, I don’t mean that I don’t like to, I CAN"T! I’d rather break the ankle than go through an ice bath!
-
raider2119
Very strange… Never had an issue with mine. Wow. -
Side note. The only thing I’ve found cumbersome about the 20# mixer is having to turn it by hand. Probably why I bought the 44# mixer and grinder to drive it. I do know if you have the mixing shaft situated a certain way it goes in and out easier. I think the paddle end down on drive end.
-
Side note. The only thing I’ve found cumbersome about the 20# mixer is having to turn it by hand. Probably why I bought the 44# mixer and grinder to drive it. I do know if you have the mixing shaft situated a certain way it goes in and out easier. I think the paddle end down on drive end.
-
Joe Hell You’re weird. You’re welcome! And as someone who sent me a copy of another manufacturers instructions, they are pretty much all made the same with slight variations and tweaks here and there!
-
PapaSop Call me weird but I enjoy the physical aspect of the mixing. It’s like exercise without the exercise!
Joe Hell
I’ve cranked enough in my day… Oops. -
Ok guys… I spent about 2 hours yesterday trying to pry the paddle out of that !!@#$ mixer… I’ve come to the conclusion the only way I’m going to get it apart is to drill out one of the brass bushings… so Jonathon If I were to do that, do you carry replacement parts?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
