Morning of fun! (long post) (okay, basically a novella)
-
kyle We are talking about the used dryer sheet? My wife ruined it by taking it out of the dirty pot! It sort of slipped my mind, but I will try it again!
Get more help with your processing questions and learn more about processing meat by subscribing to our waltonsinc.com youtube page at https://wltns.link/waltonstv I am a Gorilla, love yourself
-
kyle We are talking about the used dryer sheet? My wife ruined it by taking it out of the dirty pot! It sort of slipped my mind, but I will try it again!
-
Tex_77 I agree that a hot water rinse is best for equipment.
Maybe cold is the next best thing compared to nothing at all.
I wonder how a coating of non stick spray like PAM would work to aid with clean up?
I have also considered loading everything that would fit into the dishwasher. Maybe just all the smaller stuff and hand wash the rest.processhead I’ve used Pam on my stuffer and grinder with no problems. It definitely helps from what I can tell.
-
HerbcoFood or this years Meatgistics Christmas cards.
-
kyle Lol, I cant remember if she did or not…probably not!
-
So, it’s been a few weeks or months since I got to spend time making sausage of any kind in the test kitchen, this morning I was able to end that and got to do a few fun experiments. These will all eventually be flushed out into Meatgistics, or Meatgistics University Episodes but I wanted to give a quick rundown of what we did.
Electric Stuffer
1st, when I was up at Iowa State we spent a little bit of time in their processing room, doing some , stuffing, mixing and grinding for dried and semi-dried sausages. Actually I should say grinding, mixing, grinding, and stuffing because they did their 1st grind, mixed then went back to 2nd grind and mixed more. One of the questions we get occasionally is why we don’t mix between the 1st and 2nd grind. My response has always been that we don’t do it because a) it is unnecessary, b) it is harder to clean the grinder and c) honestly, it just wasn’t how I was taught. Turns out there is another reason, when commercial operations do this, they are going to mix in all the spices and then grind again, then go back to the mixer and add their salt and starter culture. Since we use packaged seasonings we can’t separate out the salt.
Close Up
However, I did ask the guys at the meat lab why they do this and they said they think it gives them better dispersal. I asked about how much harder it makes the cleaning and they said something that surprised me to the point I made them do it to show me. They said it doesn’t make it any harder IF you spray it down with COLD water before cleaning it. So, I just did a batch where I mixed between grinds and I added all ingredients aside from |High-Temp-Ghost-Pepper-Cheese and |Encapsulated-Citric-Acid and then ground it again, and added those ingredients. I sprayed down the grinder with as cold of water as I could get from my tap and all the meat came off pretty easily. Now, I don’t see a benefit from doing it this way BUT one of our concerns has been addressed with the Meat Hack of cleaning 1st with cold water…shocking. Also, I have begun applying white il to all surfaces that touch meat when I am done cleaning and about to put something away until I need it next time, and this could also play a role in the ease of removing this meat. But I did see these guys spray with cold water and the meat all came shooting right out.
Next we finally got the 13mm stuffing tube replacements for our Electric Stuffer while I was gone last week. We had some difficulties, or complaints about the quality of the initial batch they sent us, and we had to argue back and forth for some time, they even sent us a batch that we rejected and made them go back to the drawing board. I am very happy to announce that the 13mm stuffing tubes on the stuffer worked swimmingly! We added the full 1.5 L of water to a 25 lb batch, and we added sure gel, so it might have been a higher water content of what you would normally want. But we ran it at top speed, which is insane, should never be run that high, and it didn’t trip once, just kept pumping it out. So, the next thing to do is a few batches at lower water content and see how low we can get it. With this Stuffer there will absolutely be a requirement that a certain amount of water being added to the batch AND the only binder that is acceptable for use is the |Sure-Gel-Meat-Binder We tried the |Soy-Protein-Blend a few months ago and it didn’t work at all. I was frustrated with that but then I was talking with Brett Walton and he mentioned that when sure gel first came out one of the Meat Lab proffessor’s we speak to occasionally said that it would be the best thing to happen to snack sticks because how easy it would make stuffing. I’m rambling and just spitting out little annecdotes, sorry, I am just really happy to be back to making sausage things instead of focussing all of my attention on the website!
Old pic of Austin and Jon going insane to break up the wall of text!
We also tested a new Hand Wrapping Machine that our product development specialist (that may 100% be his title, of it could be 0% his title but its what it is in my mind) with the cling wrap and it worked well. It just holds the roll of the film, has some rollers to make applying it smooth and then a warming plate to “seal” the wrapping film.
Anyway, ton of fun this morning here aside from the cleaning!
-
So, it’s been a few weeks or months since I got to spend time making sausage of any kind in the test kitchen, this morning I was able to end that and got to do a few fun experiments. These will all eventually be flushed out into Meatgistics, or Meatgistics University Episodes but I wanted to give a quick rundown of what we did.
Electric Stuffer
1st, when I was up at Iowa State we spent a little bit of time in their processing room, doing some , stuffing, mixing and grinding for dried and semi-dried sausages. Actually I should say grinding, mixing, grinding, and stuffing because they did their 1st grind, mixed then went back to 2nd grind and mixed more. One of the questions we get occasionally is why we don’t mix between the 1st and 2nd grind. My response has always been that we don’t do it because a) it is unnecessary, b) it is harder to clean the grinder and c) honestly, it just wasn’t how I was taught. Turns out there is another reason, when commercial operations do this, they are going to mix in all the spices and then grind again, then go back to the mixer and add their salt and starter culture. Since we use packaged seasonings we can’t separate out the salt.
Close Up
However, I did ask the guys at the meat lab why they do this and they said they think it gives them better dispersal. I asked about how much harder it makes the cleaning and they said something that surprised me to the point I made them do it to show me. They said it doesn’t make it any harder IF you spray it down with COLD water before cleaning it. So, I just did a batch where I mixed between grinds and I added all ingredients aside from |High-Temp-Ghost-Pepper-Cheese and |Encapsulated-Citric-Acid and then ground it again, and added those ingredients. I sprayed down the grinder with as cold of water as I could get from my tap and all the meat came off pretty easily. Now, I don’t see a benefit from doing it this way BUT one of our concerns has been addressed with the Meat Hack of cleaning 1st with cold water…shocking. Also, I have begun applying white il to all surfaces that touch meat when I am done cleaning and about to put something away until I need it next time, and this could also play a role in the ease of removing this meat. But I did see these guys spray with cold water and the meat all came shooting right out.
Next we finally got the 13mm stuffing tube replacements for our Electric Stuffer while I was gone last week. We had some difficulties, or complaints about the quality of the initial batch they sent us, and we had to argue back and forth for some time, they even sent us a batch that we rejected and made them go back to the drawing board. I am very happy to announce that the 13mm stuffing tubes on the stuffer worked swimmingly! We added the full 1.5 L of water to a 25 lb batch, and we added sure gel, so it might have been a higher water content of what you would normally want. But we ran it at top speed, which is insane, should never be run that high, and it didn’t trip once, just kept pumping it out. So, the next thing to do is a few batches at lower water content and see how low we can get it. With this Stuffer there will absolutely be a requirement that a certain amount of water being added to the batch AND the only binder that is acceptable for use is the |Sure-Gel-Meat-Binder We tried the |Soy-Protein-Blend a few months ago and it didn’t work at all. I was frustrated with that but then I was talking with Brett Walton and he mentioned that when sure gel first came out one of the Meat Lab proffessor’s we speak to occasionally said that it would be the best thing to happen to snack sticks because how easy it would make stuffing. I’m rambling and just spitting out little annecdotes, sorry, I am just really happy to be back to making sausage things instead of focussing all of my attention on the website!
Old pic of Austin and Jon going insane to break up the wall of text!
We also tested a new Hand Wrapping Machine that our product development specialist (that may 100% be his title, of it could be 0% his title but its what it is in my mind) with the cling wrap and it worked well. It just holds the roll of the film, has some rollers to make applying it smooth and then a warming plate to “seal” the wrapping film.
Anyway, ton of fun this morning here aside from the cleaning!
-
Jonathon what issue did you encounter with the Soy Protein Blend that would make it not a desired product to use, in comparison with Sure Gel?
Spidey said in Morning of fun! (long post) (okay, basically a novella):
Jonathon what issue did you encounter with the Soy Protein Blend that would make it not a desired product to use, in comparison with Sure Gel?
I believe the minimum water additions and binder requirements are so you don’t over torque the stuffer on small diameter sausages.
-
Don’t know if its right or wrong, but I give everything a light coat of food grade silicon. I think it seems to help. If things get bad, you can always resort to the soaking with a dryer sheet. Jonathon , did you ever try my hack? Bob Stehlik said he tried it and it worked
kyle It worked for me. I tried it on an older Calphalon pan of my wife’s that varnished up. I had to do it twice, but it worked. Cleaned it up down to the original surface. Now less sticking and easier clean up.
-
Spidey said in Morning of fun! (long post) (okay, basically a novella):
Jonathon what issue did you encounter with the Soy Protein Blend that would make it not a desired product to use, in comparison with Sure Gel?
I believe the minimum water additions and binder requirements are so you don’t over torque the stuffer on small diameter sausages.
processhead My assumption was the decrease in water, although I don’t like to assume. If it was a specific problem with the Soy Protein Blend, I have a few bags I planned to try and didn’t want to run into an issue that could be avoided. I may use them on the skinless brats, instead of sticks.
-
processhead My assumption was the decrease in water, although I don’t like to assume. If it was a specific problem with the Soy Protein Blend, I have a few bags I planned to try and didn’t want to run into an issue that could be avoided. I may use them on the skinless brats, instead of sticks.
Spidey said in Morning of fun! (long post) (okay, basically a novella):
processhead My assumption was the decrease in water, although I don’t like to assume. If it was a specific problem with the Soy Protein Blend, I have a few bags I planned to try and didn’t want to run into an issue that could be avoided. I may use them on the skinless brats, instead of sticks.
I am making assumptions here as well and they are based around a goal
of achieving a meat batter that is thin enough so the electric stuffer didn’t stall out and trip the overload device.
Maybe Jonathon will chime in and clarify for both of us. -
Spidey said in Morning of fun! (long post) (okay, basically a novella):
processhead My assumption was the decrease in water, although I don’t like to assume. If it was a specific problem with the Soy Protein Blend, I have a few bags I planned to try and didn’t want to run into an issue that could be avoided. I may use them on the skinless brats, instead of sticks.
I am making assumptions here as well and they are based around a goal
of achieving a meat batter that is thin enough so the electric stuffer didn’t stall out and trip the overload device.
Maybe Jonathon will chime in and clarify for both of us.processhead Paul I am hoping to get the ruling and end our assumptions. How is your turkey season going? I tagged out here in IA in 2 morning hunts, but should have been done in one. Got busted drawing back on 2 toms or it would of been a real short hunt.
-
processhead Paul I am hoping to get the ruling and end our assumptions. How is your turkey season going? I tagged out here in IA in 2 morning hunts, but should have been done in one. Got busted drawing back on 2 toms or it would of been a real short hunt.
Spidey said in Morning of fun! (long post) (okay, basically a novella):
processhead Paul I am hoping to get the ruling and end our assumptions. How is your turkey season going? I tagged out here in IA in 2 morning hunts, but should have been done in one. Got busted drawing back on 2 toms or it would of been a real short hunt.
Congratulations on your success.
I have yet to take a shot at anything. Toms are henned up and not responding to the call. I had some move through last Saturday, but they never came in closer than 40 yards, so not within my comfort zone for a shot.
This week I have a crappy cold and just have not been motivated to get out and sit. Looks like the weather will be decent tomorrow so maybe then.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register LoginSponsored By:
