<![CDATA[Pk100.]]>My pk100. Temp is off by 100 degrees. Is it the temperature wire or is it the temperature control box. If it is the wire where is it ?

]]>https://waltonsdev.nodebb.com/topic/3584/pk100RSS for NodeThu, 10 Sep 2026 23:24:05 GMTTue, 16 Mar 2021 19:12:17 GMT60<![CDATA[Reply to Pk100. on Thu, 18 Mar 2021 06:31:37 GMT]]>No. Warranty it’s 3 years old. Controller is 140$ and the probe is $18. I ordered them right from pro smoker.

]]>https://waltonsdev.nodebb.com/post/33202https://waltonsdev.nodebb.com/post/33202Thu, 18 Mar 2021 06:31:37 GMT<![CDATA[Reply to Pk100. on Thu, 18 Mar 2021 02:58:46 GMT]]>Are you able to get the probes and control boards replaced under warranty? If not, how much are the replacement parts costing you?

]]>https://waltonsdev.nodebb.com/post/33193https://waltonsdev.nodebb.com/post/33193Thu, 18 Mar 2021 02:58:46 GMT<![CDATA[Reply to Pk100. on Thu, 18 Mar 2021 02:52:18 GMT]]>Your welcome I’ve been using the pk 100 for more then 9 years had to replace the controller and the probe the probe is no fun it’s run down on the inside of the frame.

]]>https://waltonsdev.nodebb.com/post/33191https://waltonsdev.nodebb.com/post/33191Thu, 18 Mar 2021 02:52:18 GMT<![CDATA[Reply to Pk100. on Wed, 17 Mar 2021 23:35:24 GMT]]>Thanks for the help. Temp probe is good. Tested as ohm as the new one. The controller was shot.

]]>https://waltonsdev.nodebb.com/post/33164https://waltonsdev.nodebb.com/post/33164Wed, 17 Mar 2021 23:35:24 GMT<![CDATA[Reply to Pk100. on Tue, 16 Mar 2021 23:16:07 GMT]]>Yep I do have a the instructions for the TS2 TEMP DIGITAL CONTROLLER. I got a new one that them. And I new temp probe I see how they put the probe wiring in now. So it. The probe should read. 1000 ohms at 25 c. ?

]]>https://waltonsdev.nodebb.com/post/33105https://waltonsdev.nodebb.com/post/33105Tue, 16 Mar 2021 23:16:07 GMT<![CDATA[Reply to Pk100. on Tue, 16 Mar 2021 20:50:35 GMT]]>jbird do you have the instructions for the controller if not if you want give me your email and I will send you a copy do you have a ohm meter you should see 1000 ohms at 25 °C on the probe.

]]>https://waltonsdev.nodebb.com/post/33093https://waltonsdev.nodebb.com/post/33093Tue, 16 Mar 2021 20:50:35 GMT<![CDATA[Reply to Pk100. on Tue, 16 Mar 2021 19:39:02 GMT]]>Bill Rink
Account Executive
PS Seasoning
Pro-Smoker & Roaster
800-328-8313
920-370-1684 cell
563-359-7967 Hm Office
billpsseasoning@aol.com

]]>https://waltonsdev.nodebb.com/post/33083https://waltonsdev.nodebb.com/post/33083Tue, 16 Mar 2021 19:39:02 GMT<![CDATA[Reply to Pk100. on Tue, 16 Mar 2021 19:34:59 GMT]]>Well if I set the temp at 130. It go to 230. Ave checked the temp all over the smoker. It just climbs out of control.

]]>https://waltonsdev.nodebb.com/post/33082https://waltonsdev.nodebb.com/post/33082Tue, 16 Mar 2021 19:34:59 GMT<![CDATA[Reply to Pk100. on Tue, 16 Mar 2021 19:27:05 GMT]]>You will find the temp probe behind the tin plate at the back of the smoker what I would do first is pull the controller out and check for loose wires also how are you checking to find that it is off temp the temp will vary a lot in different areas.

]]>https://waltonsdev.nodebb.com/post/33080https://waltonsdev.nodebb.com/post/33080Tue, 16 Mar 2021 19:27:05 GMT