<![CDATA[Injector, Pa's and the rest arrived.]]>I think I screwed up. If this Pa’s is as good as everyone says, this one package won’t cut it. Damn…another order?

Should the injector have come with an instruction sheet or user manual? Does Waltons have one online? Yeah, I’m one of those. Have folders full of them. Argh. Guess I could re-watch that maintenance video. Want to get the assembly right first time out.

]]>https://waltonsdev.nodebb.com/topic/1237/injector-pa-s-and-the-rest-arrivedRSS for NodeFri, 11 Sep 2026 02:54:51 GMTTue, 09 Apr 2019 20:55:14 GMT60<![CDATA[Reply to Injector, Pa's and the rest arrived. on Fri, 12 Apr 2019 21:50:03 GMT]]>Jonathon
Yep. I see that now as well. Could be just a manufacturing thing. I will still reinstall to the piece they came off of since it’s formed to that. Drseibert . I thought about rubbing a little white oil on those rings during assembly and will do that from now on. Won’t hurt them. Joe Hell . Get those rings in dude.

]]>https://waltonsdev.nodebb.com/post/4996https://waltonsdev.nodebb.com/post/4996Fri, 12 Apr 2019 21:50:03 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Fri, 12 Apr 2019 19:40:45 GMT]]>Drseibert I’ve never done that but now I think I might start recommending it. The one I took apart earlier today to compare the o-rings were a little rough. At the bare minimum, it isn’t going to hurt!

]]>https://waltonsdev.nodebb.com/post/4992https://waltonsdev.nodebb.com/post/4992Fri, 12 Apr 2019 19:40:45 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Fri, 12 Apr 2019 18:12:22 GMT]]>Jonathon Should a light coating oil be put on the O-rings before reassembly

]]>https://waltonsdev.nodebb.com/post/4990https://waltonsdev.nodebb.com/post/4990Fri, 12 Apr 2019 18:12:22 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Fri, 12 Apr 2019 16:20:17 GMT]]>PapaSop After looking at the diagram again I realized I don’t have the #6 o-ring and haven’t been using it. D’oh! (it seems to work though)

]]>https://waltonsdev.nodebb.com/post/4989https://waltonsdev.nodebb.com/post/4989Fri, 12 Apr 2019 16:20:17 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Fri, 12 Apr 2019 14:01:06 GMT]]>PapaSop I don’t think you are seeing things but I also don’t think they are technically different sizes. I think they start out the same size and then because of how the seal that goes up near the needle is used it reshapes itself and appear thinner. I stacked the seals ontop of eachother and looked through the center and did not see any difference but you could see one still had a slightly larger outside diameter.

]]>https://waltonsdev.nodebb.com/post/4987https://waltonsdev.nodebb.com/post/4987Fri, 12 Apr 2019 14:01:06 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Fri, 12 Apr 2019 01:59:02 GMT]]>Just realized this during reassembly. The two O-rings on the manifold are different. The smaller one goes on the draw tube piece. Larger on output piece. Diagram looks like same size (part 6). Checked the spare parts and definitely different. Am I seeing things? Had them reversed at first and didn’t look right.

]]>https://waltonsdev.nodebb.com/post/4983https://waltonsdev.nodebb.com/post/4983Fri, 12 Apr 2019 01:59:02 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Thu, 11 Apr 2019 18:36:11 GMT]]>Drseibert
Great idea. Actually just reassembled mine after drying overnight. C’mon weekend.

]]>https://waltonsdev.nodebb.com/post/4970https://waltonsdev.nodebb.com/post/4970Thu, 11 Apr 2019 18:36:11 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Thu, 11 Apr 2019 11:51:12 GMT]]>PapaSop I just got my injector yesterday and just watched the video on the take down an assemble. I’m going to use a fine mesh strainer to put all of the parts in while they and get rinsed off

]]>https://waltonsdev.nodebb.com/post/4965https://waltonsdev.nodebb.com/post/4965Thu, 11 Apr 2019 11:51:12 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Thu, 11 Apr 2019 00:10:46 GMT]]>Joe Hell
Actually went to garage looking for a small screen to attach to dish pan to hold small parts. Even put plug in drain so not lose anything. How anal is that?😨 Didn’t lose one piece. If this white stuff stops falling will try it out this weekend.

]]>https://waltonsdev.nodebb.com/post/4962https://waltonsdev.nodebb.com/post/4962Thu, 11 Apr 2019 00:10:46 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Wed, 10 Apr 2019 23:37:05 GMT]]>PapaSop lol. Funny you say that. I’m terrible at rebuilding carburetors and I lost parts on the injector the first time I used it.

]]>https://waltonsdev.nodebb.com/post/4961https://waltonsdev.nodebb.com/post/4961Wed, 10 Apr 2019 23:37:05 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Wed, 10 Apr 2019 22:49:01 GMT]]>1554934983109.jpg

After initial cleaning it reminded back when I used to rebuild automobile carburetors. Blew some air through the small orifices. Did not want an air/fluid lock in there. Just habit. OMG I’m old. LOL.

]]>https://waltonsdev.nodebb.com/post/4960https://waltonsdev.nodebb.com/post/4960Wed, 10 Apr 2019 22:49:01 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Wed, 10 Apr 2019 21:10:32 GMT]]>I have two of the units, and neither one came with any instructions. I did find some information on their web site which had a parts breakdown and assembly picture. I also found out extra springs can be purchased, they are small, pop out easy and very easy to loose. I love my both of my injectors they are extremely handy and easy to use. I think they are originally manufactured for something else, and re purposed for cooking. that don’t matter to me though.

]]>https://waltonsdev.nodebb.com/post/4955https://waltonsdev.nodebb.com/post/4955Wed, 10 Apr 2019 21:10:32 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:19:02 GMT]]>Jonathon
Thanks very much. Now I’ll have to start an on-line folder. LOL

]]>https://waltonsdev.nodebb.com/post/4941https://waltonsdev.nodebb.com/post/4941Tue, 09 Apr 2019 21:19:02 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:16:00 GMT]]>PapaSop what Joe Hell says about the extra spring is absolutely correct, highly recommended. Also, not getting enough Pa’s Black Bull on your first go-round is totally understandable, better to have to order again than be stuck with a large amount in the unlikely scenario that you dont end up liking it! Here is a breakdown of the injector.

https://admin.waltonsinc.com/media/catalog/product/2/2/222162-auto-injector-part-breakdown.jpg

]]>https://waltonsdev.nodebb.com/post/4940https://waltonsdev.nodebb.com/post/4940Tue, 09 Apr 2019 21:16:00 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:12:54 GMT]]>Joe Hell
I already did. As you suggested in a previous post. Thank you. Will watch the videos again…Just how I roll.👍

]]>https://waltonsdev.nodebb.com/post/4938https://waltonsdev.nodebb.com/post/4938Tue, 09 Apr 2019 21:12:54 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:07:47 GMT]]>PapaSop I would also suggest adding the replacement springs to your next shopping cart. Better safe than sorry!

]]>https://waltonsdev.nodebb.com/post/4936https://waltonsdev.nodebb.com/post/4936Tue, 09 Apr 2019 21:07:47 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:06:44 GMT]]>PapaSop Yup!

]]>https://waltonsdev.nodebb.com/post/4935https://waltonsdev.nodebb.com/post/4935Tue, 09 Apr 2019 21:06:44 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:04:44 GMT]]>Joe Hell
So this is assembled ready to go? The washer/o-rings in separate bag are spares?

]]>https://waltonsdev.nodebb.com/post/4934https://waltonsdev.nodebb.com/post/4934Tue, 09 Apr 2019 21:04:44 GMT<![CDATA[Reply to Injector, Pa's and the rest arrived. on Tue, 09 Apr 2019 21:01:34 GMT]]>I don’t remember if I got a manual but it seems like there wasn’t much info that came with it. I’d highly recommend taking picture as you disassemble the first time and be really careful not to lose the springs…like I did. These videos should help!

https://meatgistics.waltonsinc.com/topic/907/meat-processing-equipment-201-maintenance-for-automatic-syringe-injectors

https://www.youtube.com/watch?v=LCd4xMmMt-A

]]>https://waltonsdev.nodebb.com/post/4933https://waltonsdev.nodebb.com/post/4933Tue, 09 Apr 2019 21:01:34 GMT